I'm interested in working remotely- very remotely off-grid in fact. How can I power a Macbook Pro & related peripherals using Solar Power?

  • 5
    If you have other questions about solar power and off-grid living then you might be interested in the Sustainable Living StackExchange site.
    – Nic
    Commented Mar 7, 2020 at 15:15
  • Thanks @Nic ! Didn’t even know it existed! Only posted to this group because I use a Mac and was interested in keeping it powered when taking a break from the rat race. Thanks for letting me know about that one. Definitely would be interested in it!
    – F1Linux
    Commented Mar 7, 2020 at 15:19

5 Answers 5


I've worked as far afield as Northern Nigeria as a technologist (Infrastructure & Network Engineering), where reliable power is always an issue. Indeed, reliable energy is a problem endemic to many lesser developed nations across the globe. Closer to home, many folks are looking to go off-grid to escape the rat-race but still want to stay connected to the wider world.

Since powering a Mac (my solution can be used to power any AC device) seemed of broader utility to a wider audience, figured I'd share my documentation on design considerations & physical connectivity to save others solving the same-very complex - problem. Lots of annotated pictures are included at end of post to visually detail the physical connectivity between the components.

  1. SYSTEM OVERVIEW: I'll explain the system conceptually in (2) parts:
    1. COLLECTION: Solar Panels sends Direct Current (DC) to a 12v battery (also DC) via a “Solar Controller” that regulates transfer of DC from panels to battery to ~12v. Without a Solar Charge Controller the Solar Panels could create an over-voltage condition sending as much as 20v+ to a 12v battery.
    2. DISTRIBUTION: On the other side of the battery an “AC Power Inverter” is connected that converts battery’s Direct Current (DC) to Alternating Current (AC) when connected end-user devices draw power.
    3. POWER EQUILIBRIUM: The COLLECTION side of the system should ideally replace what is being drawn from battery on DISTRIBUTION side. If more is drawn out than replaced, battery will start to drain to its' Depth of Discharge ("DoD) limit and the inverter your devices are connected to will cut-out.
  2. CHOOSING SYSTEM COMPONENTS: Key considerations:
    1. SOLAR PANELS: These convert sunlight to DC which is sent to a 12v battery (also DC) for storage. The Solar Panel’s nominal wattage is sum of all panels configured into in an array: ie, my 200 watt solar panels are actually an array of (4) x 50 watt solar panels.
      1. SOLAR PANEL EFFICIENCY: you’ll see a figure such as “19.8” in the manufacturers specs. So for my 200 watt panels, that would be the conversion of 1000 watt/m2. Under ideal test conditions. The Earth rotates and both duration of sunlight & intensity can vary with both season & geography. “200 watts” is nominal; effective wattage will be some degree less.
      2. APPROPRIATE WATTAGE: Calculate your power requirements FIRST and THEN buy Solar Panels that will keep the battery topped-up at at least the same level devices are drawing power from the battery. You can only know what panels you require after you’ve determined what devices you want to power with the Solar Power System ie, a 96 watt 2018 MacBook and a printer of X watts
      3. WEIGHT: My 200 watt panels panels weigh 5.15 KGs. If I bought the 150 watt model- (3)x50watt- I could have reduced their weight by 25%. Keep wattage sizing of panels as close to your actual power requirements as possible to avoid killing your luggage weight allowance.
      4. PHYSICAL DIMENSIONS: Check length & width measurements of any panels (fully folded) BEFORE buying to ensure they’ll fit in your suitcase!
    2. SOLAR CHARGE CONTROLLER: This device sits between your solar panels and battery storing panel’s DC output. Controller regulates flow of electricity from panels to battery ensuring panels don’t send 20v to a 12v battery.
      1. (2) Types: “PWM” vs “MPPT”: Ref: https://www.solar4rvs.com.au/buying/buyer-guides/choosing-the-right-solar-charge-controller-regulat/
        2. MPPT (“Maximum Power Point Tracking”):
      2. REDUNDANCY: If Controller fails, you’re out of the game. They’re not expensive and very lightweight, so only a downside to not keeping a spare.
      3. BATTERY COMPATIBILITY: Ensure battery to be connected to Solar Controller compatible with battery. Do NOT connect the Controller to any random battery without checking compatibility, or you could damage the Controller. The Controller’s user manual should have have details about battery compatibility, providing codes for battery types that work with it. Batteries will be discussed in §3 “12v BATTERY”(only b00-b03). Use below list to interpret codes specified in the Controller’s manual if required:
        1. b00: Lithium Battery
        2. b01: Sealed Battery
        3. b02: Gel Battery
        4. b03: Flood
        5. b04: Iron Lithium 4 strands
        6. b05: Iron Lithium 5 Strands
        7. b06: Lithium Ion 3 Strands
        8. b07: Lithium Ion 4 Strands
    3. BATTERY: The 12v battery receives DC output from Solar Panels (via Solar Charge Controller) and also supplies an Inverter connected to it which converts battery’s DC power to AC for end-user devices; your MacBook. You require a battery “vocabulary” when Googling to source an appropriate one, or you either won’t know what to search for, or won’t be able to interpret the results.
      1. COMPATIBILITY WITH SOLAR CONTROLLER: Read your Controller’s user manual to determine what battery to source. Using a battery which is NOT can potentially damage Controller!
      2. BATTERY CAPACITY (Ah): A battery’s capacity is described in terms of “Ah” (“Amp Hour”), ie, a 100 Ah battery theoretically can power a 1 amp device for 100 hours, or a 10 amp device for 10 hours. However, this is a nominal number and MUST be multiplied by battery's “Depth of Discharge” to determine practical capacity of the battery.
      3. DEPTH OF DISCHARGE” (“DoD”): Large 12v batteries are not designed to be fully drained like a flashlight’s batteries. DoD is the *USABLE capacity of a battery’s Ah rating, ie, a 100 Ah battery with a DoD 50% means that for all practical purposes your inverter is connected to a 50Ah battery. Forget the other 50Ah, you can’t use it...
        1. STARTING, LIGHTING, IGNITION “SLI”: Batteries designed to start a car and power its’ lights. “STI” batteries NOT desirable for use with Solar Power Systems. Shallow Depth of Discharge cycles- around ~10%. Not very suitable for Solar Power Systems.
        2. DEEP CYCLE: Ideal battery for Solar Power Systems. Deep Cycle batteries are designed to have a much greater DoD over a sustained period- usually around 50%- then cranking batteries which can have a DoD of as high as 70%. Check both Amazon & Google “12v Deep Cycle Batteries” and you’ll see many shops selling them in the following flavours:
          1. LEAD ACID BATTERY: Although “CALCIUM” is a type of “LEAD ACID” battery, it’s found in “SLI” (cranking”) batteries and should be avoided. You’d probably be better off using a cigarette lighter powered inverter to power your devices off the rental vehicle’s battery. (2) Types Lead Acid Batteries:
            1. FLOODED: When the term “FLOODED” is seen in a Solar Controller’s user manual it’s referring to a “wet” Lead Acid Battery found in cars. Being “flooded”, not desirable for environments of extremes of hot & cold. Identified by both apertures to add water and a “sloshing” noise when moved. Cheaper to buy & have excellent comparative useful life, but require maintenance. Unless you’re willing to be bothered maintaining them, avoid Flooded batteries.
            2. VALVE REGULATED LEAD ACID (“VRLA”): Unlike “Flooded” batteries which CAN’T be sealed because of the need to add water to them, VRLA batteries are referred to as “SEALED** because they require no/little maintenance. More expensive than “Flooded” batteries. (2) Types:
              1. Absorbed Glass Mat (“AGM”)
              2. GEL
          2. LITHIUM ION BATTERY: More expensive than LEAD ACID batteries and only have a 3 year life- regardless of use.
      5. SIZING BATTERIES: Let’s put it all together. Your goal is to ensure the battery remains level- putting in an amount equal to what the devices connected to the inverter are sucking out of it. You want to avoid- or delay- as much as possible more draw-down than top-up as if you slip down to the DoD max, the inverter will (hopefully) start beeping and just shutdown. Ideally, size the battery a bit larger than you require- unless you can guarantee tomorrow won’t be a cloudy day. Since the Battery is rated in Ah, and our panels and inverter watts, we need to convert watt hours (“Wh”) for the panels and devices drawing on the battery through the inverter into Ah. 
Using an example of 200 watt Solar Panels charging the battery and (2) x 96 watt MacBook Pros (2018) drawing on that battery for a 1 hour period:
 Solar Panels: 200 Watts x 1 hour = 200 Wh
. MacBook: 192 Watts x 1 hour = 170 Wh. 
Next convert Wh into Ah:
 Solar Panels: 200 Wh / 12.7 volts = 15.74 Ah (Power Collection)
. MacBook: 192 Wh / 12.7 volts = 15.12 Ah (Power Distributed) (https://convert-formula.com/ah-wh)
. If you had a 75 Ah cranking battery with a DoD of 10%, that’s just 7.5 Ah available for the two MacBooks. And not even that! there’s about ~10% loss when the Inverter converts the DC from the battery to AC for the MacBooks! Hopefully this underscores the importance of both using Deep Cycle batteries.
      6. SOURCING BATTERY ABROAD: Identify sources that sell/rent DEEP CYCLE batteries types compatible with your Solar Controller BEFORE travelling, or risk spending 1 or more days searching for suitable batteries or failing altogether. In the US or Europe sourcing a Deep Cycle battery should be possible, but the more remote your destination, the more challenging sourcing a battery for your Solar Power System in-country will be.
    4. INVERTER: Converts battery’s Direct Current (DC) to Alternating Current (AC) when drawn by devices connected to inverter.
      1. TYPES:
        1. PURE SINE WAVE: Best voltage waveform output, works with all devices
        2. MODIFIED SINE WAVE: Cheaper alternative than Pure Sign Wave, but CAN (not guaranteed) introduce interference into audio equipment, monitors & TVs. Not recommended for devices with “high surge” startup power requirements. Modified sine wave also might not work with power tools and/or battery chargers for cordless tools. Finally, I’ve read many people are using modified sine wave inverters to power computers without problems; YMMV…
      2. APPROPRIATE WATTAGE: (2) things you need to consider when choosing a wattage.
        1. INVERTER CONTINUOUS AC OUTPUT POWER: If the inverter is “1000” watts and the continuous wattage is 1000 watts, theoretically you should be able to power 10 x 1000 watt devices (assuming the battery and solar panels can support that!). However, I bought a 500 watt Modified Sine Wave Inverter (it was cheap) only to read in the user manual the *continuous, was just 400 watts; 20% less than then advertised. Do your homework to avoid surprises. First determine your wattage requirements for the devices you’ll connect to it.
        2. INVERTER SURGE POWER: Check surge power wattage of inverter you’re considering buying can additionally meet surge power demand to accommodate any devices being greedy on startup.
        3. CALCULATION: Add the wattage of the devices that you want to power off the inverter; it’s simple addition. ie, (4) x 96 watt MacBook Pros 2018 and (1) x 85 watt MacBook Pro (2014) equals 469 watts. My “500” watt Modified Sine Wave inverter would be insufficient for these requirements… I’d recommend using a Pure Sine Wave over the Modified and sizing the wattage higher than you require.
      3. EFFICIENCY RATING: Percentage of DC input that is converted into AC output by inverter. ie, an efficiency rating of 90% implies a 10% loss from the conversion. So on the COLLECTION side of the system you need to factor this loss into your calculations sizing the Solar Panels & battery.
      4. Inverter Cables Sizing: Although cables are packages with an inverter, If you need to buy longer ones, ensure you buy the correct gauge for your inverter’s wattage:
 General Recommendations:
 (Inverter Size/Cable Gauge)
 1000 Watts/#4
, 1500 Watts/#2
, 2000 Watts/#1/0
, 2500 Watts/#1/0
, 3000 Watts/#3/0
  3. INSTALLATIONS INSTRUCTIONS: Physical Connectivity
      1. Solar Panels: Closed (folded)
      2. Inverter: Switched to the “Off” position
        2. Positive last
      3. Connect INVERTER to BATTERY
      1. Disconnect INVERTER from BATTERY
        2. Negative Last

The connections should look as follows:


That may seem a lot, but trust me: this is a huge subject and to condense all the key detail into this was a huge effort. Hope it helps others trying to work off-grid tapping away happily on their MacBooks (or Min-Macs, iMacs, etc....). I'll post the link to accompany this post which shows me charging my 85 watt MacBook 2014 using solar panels shortly. Video is done, just have to render it and upload to YouTube, but thin connectivity at the 'mo.


Having returned from the Omani Desert and sourcing a 5 meter extender cable to allow placing the battery and the inverter in the shade away from the solar panels, I've had a moment to pictorially document a more ideal configuration.

To avoid any ambiguity or confusion, everything is expressly labelled.

Gel Battery










The Grounding Rod & cable for the inverter cost me the princely sum of £6.50: InverterGroundingRod


If you still require further clarification, I've also created a companion video implementing my portable Solar Power solution in Oman which should fill in any questions about how confguring a portable solar power system-

  • 1
    May thanks for this extremely detailed and useful info. I was wondering what other options there are for generation other than solar power?
    – benwiggy
    Commented Mar 7, 2020 at 12:10
  • 2
    @benwiggy No prob! Anytime I run across something that is hurt-your-head complicated, I feel compelled to share my documentation so others don't cover the same ground, solving the same problem. I guess wind would be an alternative for days the Sun isn't cooperating. That's actually next on my list of alternative energy sources for working remotely. Instead of using sunlight to top-up the batterry, you'd use a wind turbine. Not sure how portable such a solution would be though. When I work it out next, I'll post the solution!
    – F1Linux
    Commented Mar 7, 2020 at 12:20
  • I've read that bicycle generators can produce 100W, so that's disappointing.
    – benwiggy
    Commented Mar 7, 2020 at 12:33
  • @benwiggy I used to jump with one of those when I was in US Army SF. Portable, but a bit heavy-ish. We took turns peddling the thing to charge the team's radio batteries. I'll stick with solar ;-)
    – F1Linux
    Commented Mar 7, 2020 at 12:36
  • Thank you very much for this detailed report! Did you thought about a direct DC->DC solution without the DC->AC->DC convertion? I am thinking about a 12v->20v converter and from there via USB TYP-C for 40-50W Input into the macbook (e.g. via QuickCharge). It should run fine on that level and loads when idle. What do you think @F1Linux ?
    – gies0r
    Commented Dec 29, 2020 at 17:13

I have just built a system to meet the same need.

I brought a 200w panel, 500w inverter and 140HA deep cycle battery. The setup cost me around $1000 NZD (new zealand)

Were in lockdown so i had to make do with what i had at hand for mounting (hand saw, battery drill and scraps of wood).

I found that if i charge my macbook pro to 100% on the inverter via the mains charger (80w), i can then run it for 10-15hrs via usb c on lower power requirements (25w 12v usb/cigarette adaptor).

Initially i cycled charging the laptop, disconnecting the charger, use until flat and recharge on the mains charger. I found a full battery would only last around 8 days in inclement weather with solar connected vs about 3 days on batteries alone.

I intent to add another 200w panel to cover the reduced sun over winter.

enter image description here

enter image description here

  • Ohhhhhh, that’s sexy. Up vote for that!
    – F1Linux
    Commented Apr 22, 2020 at 9:58
  • The panels held in with blocks of plywood wrapped in bicycle tube and electrical tape. And its pretty obvious i couldn't be bothered cutting to many peices of wood to length. I since added legs that give me a better angle for optimum charge that rest on the box when the lids off to make it easier to work on
    – Whojarr
    Commented Apr 22, 2020 at 10:04
  • It’s a different world we’ll live in post lockdown and solutions like this which drive self-sufficiency will be the new currency on the ‘net. Used to just be preppers interested in this stuff, but I suspect things like this will become mass-market. Great solution bud!
    – F1Linux
    Commented Apr 22, 2020 at 10:14

If you don’t want a do it yourself system. And you have a couple of thousand dollars, then you could purchase a couple of Jackery Portable charging stations and power each one with a portable Jackery solar panel array. I use the brand name just to point out that there are integrated off the shelf solutions.

It takes a long time to fully charge up a backup battery with a solar panel. So the 2 station setup probably doesn’t support a heavy computer usage scenario. But it’s clean and compact and portable and relatively light weight. And might put you into another path of investigation even if these don’t cover all your usage.

Two portable lithium batteries each with a collapsible solar panel array:

Amazon Jackery Power Station

Amazon Jackery Solar Panel


I would suggest buying a caravan power module which can run from mains, a solar panel or DC 12v (and charge a 12v battery), all in one box - they can deliver 12V 40A to/from the battery... and if Your laptop is powered from USB C do not use an inverter, use a 12v to USB C PSU instead.

I use a Shaudt CSV409 and a 100Ah 12v LiFePo battery from Fraron (with internal BMS). That gives a weight of about 15kgs (11 for battery + 4 for CSV409), all that is in my caravan but it could as well be in a box.


Assuming the solar panels are used to charge 12 volt batteries, and your MacBook Pro is new enough to use USB-C for power, then the solution is quite simple. All you need is an off the shelf USB-C car charger. I found one from Aukey that will supply 9 volts at 3 amps from a 12 volt automotive accessory outlet, also known as a cigar lighter socket. This isn't great for powering the laptop at full power continuously but it's enough to keep it running with light loads continuously, or for an overnight recharge after running full power.

This will also apply to any peripherals that can run on USB-A or USB-C, use a car charger. Most every car charger I've seen will take a wide range of voltages so don't be too concerned if your battery pack is 24 volts instead of 12 volts, just look closely at the specs before you buy.

In addition to Aukey I'll mention another company I have been satisfied with their products, Powerwerx. Powerwerx sells all kinds of products for going off grid, including a panel mount USB charger. https://powerwerx.com/panel-usbc-pd-power-delivery-qc30-blue

That charger is only 18 watts, not 27 watts like the Aukey one I mentioned before. It might still work for you though. Also on their site is all kinds of cables, wires, and adapters to hook up solar panels, batteries, and other stuff. And they sell the solar panels, batteries, and other stuff too. This isn't a paid endorsement, I'm just a happy customer.

  • Thanks for adding an answer. I don’t know what to make of this sentence “ don't be too concerned if your battery pack is 24 volts instead of 12 volts, just look closely at the specs before you buy.” wouldn’t a close look catch a 2 volt difference, let alone 12? Can you explain what specs need looking at if not voltage?
    – bmike
    Commented Sep 30, 2020 at 12:58
  • 1
    My point is that a "12 volt" car charger is rarely rated for only 12 volts. A close look at the specs should show that they will be rated for a voltage range as narrow as 11 to 16 volts or as wide as 9 to 32 volts. Either will work fine on a nominally 12 volt battery pack but the second will also work on a nominally 24 volt battery pack. If you have a 24 volt solar panel and battery pack then finding a compatible USB charger that can run at that voltage should not be difficult, most any off the shelf charger is rated for 24 volts. Just look closely that 24 volts is supported before you buy
    – MacGuffin
    Commented Oct 1, 2020 at 16:07
  • That makes sense - thanks for the clarifying comment
    – bmike
    Commented Oct 1, 2020 at 16:10

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .