"Select CD-ROM Boot Type:" error during Windows install

Question

Which version of bootcamp 4.x do I need to install Windows 7 (64 bit) on an iMac7,1 with Yosemite?

Specs: 64 bit Core 2 Duo, 4GB, 16GB Flash, optical drive, Windows 7 install DVD

Everything goes fine until during the install process Mac reboots to install windows then:

1
2
Select CD Rom boot type:

I can't enter anything because keyboard and mouse are unresponsive and I assume the correct drivers were not loaded.

iMac is mid 2007 24" 64 bit (says profiler/other internal monitors). Have downloaded various boot camp versions, followed documented instructions, stood on my head and spit nickels, and still get same error (Select CD Boot ROM type). Made ISO file with Mac Disk Utility (create and change .cdr to .iso) Didn't work either.

After further review, seems that I misread Apple support table which show this model uses Boot Camp 4 for 32-bit Windows 7. Genius - bought install DVD for 64-bit :-o So I guess that's why it won't install.

Going to try suggested method of creating ISO from W7 store-bought DVD on Windows machine just for giggles and see what happens. Then probably go buy the correct DVD for 32-bit :-( Thanks for the info :-)

Answer 1

The problem you encountered occurred before the Boot Camp drivers are installed. So, the drivers are not the problem. The correct drivers for Macs can be found at Install Windows 7 on your Mac using Boot Camp. In your case, the drivers can be downloaded from Boot Camp Support Software 4.0.4033. Also, the drivers can be downloaded using the Boot Camp Assistant. By the way, I used the same drivers to do a clean install Windows 8 (64 bit) on my iMac7,1 (20-inch, Mid 2007).

Your actual problem is with the DVD itself. As you might guess, it came with two ways to boot. You need to remove one of them. You are using a Windows 7 DVD. I was having the same problem with a Windows 8.1 (64 bit) DVD. The procedure to repair should be the same.

I used a windows 8.1 machine and a copy of the program oscdimg.exe from Microsoft. The procedure should work just as well using a Windows 7 or 10 machine.

To begin, you will need to copy oscdimg.exe to your desktop. There are many web sites where a copy of this file can be found. I used oscdimg.exe Version 2.55 (x86). If you want to be sure you are using the same one I used, follow the steps below.

1. Go to the web site The Windows® Automated Installation Kit (AIK) for Windows® 7 and download the iso. This iso file is 1.7 GB in length.

2. Open the file Neutral.cab. If you are using a Windows 7 machine, you will need to burn the iso on to a DVD. The instructions can be found here. Open the new DVD to find the Neutral.cab file. It is faster to copy the Neutral.cab file to the desktop before opening it. If you are using a Windows 8.1 or 10 machine, right click on the iso icon and select Mount. Neutral.cab will be one of the files in the opened folder. (Note: Opening the file can take a while.)

   One way to avoid burning a DVD would be to copy (or download) the iso file to a machine running OS X. The iso file can then be mounted by double clicking on its icon. Neutral.cab will be one of the files in the opened folder. You will need to copy Neutral.cab back to a Window machine. I tested this using OS X 10.6.8. I assume this procedure would work using any newer version of OS X.

   Another way to avoid burning a DVD would be to copy (or download) the iso file to the ~/Downloads folder of a machine running Kubuntu (or perhaps some other Linux). The following commands can be used to extract the Neutral.cab to the ~/Downloads folder. You will need to copy Neutral.cab back to a Window machine. I tested this using Kubuntu 18.04.5 LTS.

   cd ~/Downloads
   mkdir windowsiso
   sudo mount -o loop,ro KB#AIK_EN.iso windowsiso
   cp windowsiso/Neutral.cab .
   sudo umount windowsiso
   rmdir windowsiso
   

3. Using a Windows 7, 8.1, or 10 machine, extract oscdimg.exe from the Neutral.cab cabinet file. The x86 (32 bit) version is named F1_oscdimg. The x64 (64 bit) version is named F3_oscdimg. Right click on the file of your choice and select Extract. Place the extracted file on your desktop. Rename the extracted file to oscdimg.exe. (I did verify the correctness of this procedure by installing the entire package and binary file comparing the installed x86 and x64 oscdimg files with F1_oscdimg and F3_oscdimg, respectively.)

Next, make a new Windows 7, 8.1 or 10 installation DVD, follow these steps. The procedure was tested using a Windows 8.1 installation DVD.

1. Make sure a copy of oscdimg.exe is on your desktop.

2. Place the original Windows 7, 8.1 or 10 installation DVD in the optical drive. If using a Windows 8.1 or 10 machine, then a Windows 7, 8.1 or 10 installation iso file could be mounted instead.

3. If you are using a Windows 7 machine, open a Command Prompt window by clicking the Start button , clicking All Programs, clicking Accessories, and then clicking Command Prompt. On a Windows 8.1 machine, look for the Command Prompt icon on the Apps page. On a Windows 10 machine, look for Command Prompt under Windows System on the Start menu.

4. Change your working directory to the desktop by entering the following command in the Command Prompt Window.

   cd  %homepath%\desktop
   

5. Assuming D: is your DVD drive or drive letter assign to the mounted Windows installation iso file, enter the following command. Be sure to replace the letter before each : with the drive letter of your DVD drive or mounted file. The file new.iso will be created on your desktop.

   oscdimg  -n  -m  -bD:\boot\etfsboot.com  D:\  new.iso
   

   Note: For more information, see the Microsoft website Oscdimg Command-Line Options.

   Using this command, on a Windows 8.1 (64 bit) DVD, produced the following output.

   C:\Users\David\Desktop>oscdimg -n -m -bD:\boot\etfsboot.com D:\ new.iso
   
   OSCDIMG 2.55 CD-ROM and DVD-ROM Premastering Utility
   Copyright (C) Microsoft, 1993-2007. All rights reserved.
   Licensed only for producing Microsoft authorized content.
   
   
   Scanning source tree (2000 files in 803 directories)
   Scanning source tree complete (2094 files in 867 directories)
   
   Computing directory information complete
   
   Image file is 3277371392 bytes
   
   Writing 2094 files in 867 directories to new.iso
   
   100% complete
   
   Final image file is 3277371392 bytes
   
   WARNING: This image contains filenames and/or directory names that are
    NOT COMPATIBLE with Windows NT 3.51. If compatibility with
    Windows NT 3.51 is required, use the -nt switch rather than
    the -n switch.
   
   
   Done.
   
   C:\Users\David\Desktop>
   

6. Burn new.iso on to a DVD. The instructions for a Window 7 machine can be found here. The same instructions can be used for a Windows 8.1 machine. For a Windows 10 machine, find the new.iso file in the File Explorer, then right click on the new.iso file and select Burn disc image.

   Note: The current 32 bit Windows 10 (20H2) release can be burned to a DVD or a rewritable (RW) DVD. However do to the larger size, the current 64 bit Windows 10 (20H2) release can only be burned to a dual layer (DL) DVD.

   You can also transfer the new.iso file to a OS X machine and burn to a DVD using the Disk Utility.

7. Finally, install Windows 7, 8.1 or 10 using the new DVD.

Answer 2

I ran into this same issue on my iMac 2007 model with Yosemite installed. I used the 64 bit disk and got the select CD-ROM boot type message and my keyboard/mouse was non responsive. I powered off my Mac and then ejected the disk and put in the 32 bit Windows install disk instead and the installation continued like nothing was ever wrong. So the issue in my case was that the installation for Boot Camp needed the 32 bit version of Windows 7 not 64 bit. I hope this helps someone else also. :)

Answer 3

1. After selecting CD as boot device, immediately press "1" on your keyboard and keep it pressed.
2. When you see a black flash, press enter (without releasing "1"). This happens twice, press enter both times.
3. Keep "1" pressed until you see the disc has actually began booting.

Source: https://medium.com/@mark.stanislav/fixing-select-cd-rom-boot-type-when-booting-windows-or-linux-on-a-mac-76bde5d6a593#.dl3olstb9