Take the 2-minute tour ×
Ask Different is a question and answer site for power users of Apple hardware and software. It's 100% free, no registration required.

On a Linux machine, I can see my IPv6 neighbors using the following command (Also see the Linux IPv6 HOWTO:

    # ip -6 neighbor show
    2002:333:333::1 dev eth1 lladdr 00:12:1e:33:AA:BB router REACHABLE

What is the equivalent command on a Mac (currently running Snow Leopard)?

share|improve this question
add comment

1 Answer

up vote 3 down vote accepted

Short answer:

mir:~ itorres$ ndp -an
Neighbor                        Linklayer Address  Netif Expire    St Flgs Prbs
::1                             (incomplete)         lo0 permanent R      
2001:470:95e5:1:3583:ead0:514d:d459 e8:6:88:ca:fd:7c en0 permanent R      
2001:470:95e5:1:ea06:88ff:feca:fd7c e8:6:88:ca:fd:7c en0 permanent R      
...

Longer answer:

You're in UNIX and you have two great commands: man (system manual) and apropos (lookup concepts on manual)

Hence:

mir:~ itorres$ apropos ipv6
Net::CIDR::Lite(3pm)     - Perl extension for merging IPv4 or IPv6 CIDR addresses
Net::IP(3pm)             - Perl extension for manipulating IPv4/IPv6 addresses
NetAddr::IP(3pm)         - Manages IPv4 and IPv6 addresses and subnets
NetAddr::IP::Lite(3pm)   - Manages IPv4 and IPv6 addresses and subnets
faith(4)                 - IPv6-to-IPv4 TCP relay capturing interface
icmp6(4)                 - Internet Control Message Protocol for IPv6
inet6_opt_init(3), inet6_opt_append(3), inet6_opt_finish(3), inet6_opt_set_val(3),     inet6_opt_next(3), inet6_opt_find(3), inet6_opt_get_val(3) - IPv6 Hop-by-Hop and     Destination Options manipulation
inet6_option_space(3), inet6_option_init(3), inet6_option_append(3), inet6_option_alloc(3    ), inet6_option_next(3), inet6_option_find(3) - IPv6 Hop-by-Hop and Destination Options     manipulation
inet6_rth_space(3), inet6_rth_init(3), inet6_rth_add(3), inet6_rth_reverse(3),     inet6_rth_segments(3), inet6_rth_getaddr(3) - IPv6 Routing Header Options manipulation
inet6_rthdr_space(3), inet6_rthdr_init(3), inet6_rthdr_add(3), inet6_rthdr_lasthop(3),     inet6_rthdr_reverse(3), inet6_rthdr_segments(3), inet6_rthdr_getaddr(3),     inet6_rthdr_getflags(3) - IPv6 Routing Header Options manipulation
ip6(4)                   - Internet Protocol version 6 (IPv6) network layer
ip6(8)                   - Enable or disable IPv6 on active interfaces
ip6config(8)             - Configure IPv6 and 6to4 IPv6 tunnelling
ip6fw(8)                 - controlling utility for IPv6 firewall (DEPRECATED)
ndp(8)                   - control/diagnose IPv6 neighbor discovery protocol
tcllib_ip(n)             - IPv4 and IPv6 address manipulation
traceroute6(8)           - print the route IPv6 packets will take to a network node

To get more detail about ndp:

mir:~ itorres$ man ndp
share|improve this answer
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.