Take the 2-minute tour ×
Ask Different is a question and answer site for power users of Apple hardware and software. It's 100% free, no registration required.

I followed the guide at http://macperformanceguide.com/SnowLeopard-64bit.html to boot into 64-bit mode. I had no problems with the instructions and on the boot screen it says "PAE enabled, 64bit mode enabled" but when the system boots, both uname -a and System Profiler tell me that it has booted into 32-bit mode.

I really need to boot into the 64-bit kernel, what should I do?

System is MacBook Unibody (Early 2009, 6 GB RAM, 2.4 Intel CPU, 10.6.6)

share|improve this question
    
Why do you "need" to boot into the 64-bit kernel? It's not necessary for anything... –  Itai Ferber Mar 16 '11 at 1:32
    
There are several methods listed on that page. Did you try all of them? Same results for all? Please refine question with more details. Don't just link to that page, tell us what you did. –  user588 Mar 16 '11 at 2:53
    
@mankoff: I tried all and all combinations, no results. I did them all. –  AbiusX Mar 16 '11 at 3:27
    
@itaiferber: I explicitly told that I need to do so, hence your comment was flagged as bugous. I have libs that link against 64bit kernel modules. –  AbiusX Mar 16 '11 at 3:27
1  
Note that the message "PAE enabled, 64bit mode enabled" does not mean the 64-bit kernel was used. But I guess that's obvious to you now :) –  ghoppe Mar 16 '11 at 16:01

5 Answers 5

up vote 6 down vote accepted

64-bit Mac CPUs cannot boot 64-bit kernel due to one of the following reasons:

  1. The machine has 32-bit EFI.
  2. The machine’s model is prohibited from booting K64 through a hardcoded list within the boot loader. (The list excludes "non-Pro" machines.)

Both limitations are artificial and imposed by Apple, although the first one is important because if a 32-bit EFI were allowed to boot the kernel wouldn't be able to use firmware services.

IF you really, really, really want to boot these machines with a 64-bit kernel, you'll need to perform hackery on /System/Library/CoreServices/boot.efi. This is quite risky. More info:

http://osxbook.com/blog/2009/08/31/is-your-machine-good-enough-for-snow-leopard-k64/

share|improve this answer
    
But my EFI is 64 bit, And 64 bit is enabled on boot (as it says) But only when I boot it sais 64bit not loaded. –  AbiusX Mar 16 '11 at 20:00
    
Because your machine is not PRO, you cannot do it unless you try to modify the efi (as described by ghoppe in his link). There's a list that excludes your machine, no matter how 64 bits EFI you have. –  Martín Marconcini Mar 17 '11 at 0:31
    
Unfortunately the boot.efi defined in that article is too old and its hash is not the same as mine, So the byte refered to not found. Any more recent instructions? –  AbiusX Mar 17 '11 at 12:53

64-bit kernel mode is not supported on any of the MacBooks (see Apple's KB article #HT3770), even if they have a 64-bit CPU and 64-bit EFI firmware. I don't know why it's not possible to boot them 64-bit, but I haven't found a way to do it (I'm in the same boat, as I have a 2007 MacBook Pro, also 64-bit EFI, but Apple only supports 64-bit kernel on the MacBook Pros introduced in 2008 or later).

share|improve this answer
    
But mine is 2009? –  AbiusX Mar 16 '11 at 19:59
3  
@AbiusX: According the Apple KB article, MacBook Pros since 2008 can boot K64; none of the non-Pro MacBooks can. Sorry. –  Gordon Davisson Mar 16 '11 at 22:26
    
Well a month after i bought this, this was changed to pro. Nothing changed but only the name. –  AbiusX Mar 16 '11 at 22:42
    
@AbiusX You really don't know if "only the name" changed, maybe some other internal, in either case, the answer is simple, you cannot boot into 64 bits with a "non pro" Macbook, unless you try the boot.efi modification (which is risky) but might work. –  Martín Marconcini Mar 17 '11 at 0:32
    
@Martin: I think modification of boot.efi wont be so risky, i can simply time machine back to my old system if anything goes wrong, right? Would u please provide me with modification instructions? –  AbiusX Mar 17 '11 at 0:40

There is a plist at /Library/Preferences/SystemConfiguration/com.apple.Boot.plist which controls which kernel gets used at boot time.

You can hold 6 & 4 to boot into 64-bit kernel mode while booting. Also, you can boot 32-bit by holding 3 & 2 while booting. Or you can try

sudo systemsetup -setkernelbootarchitecture x86_64

and then reboot.

share|improve this answer

I have the same computer as you.

There is no way to boot in 64 bit mode.

I tried modifying so many system files. It cannot be done, and it does not need to be.

share|improve this answer
    
If you haven't found a way, Do you think it means that there are non? –  AbiusX Mar 16 '11 at 20:23
1  
Given the amount of searching I did, yes. –  user4464 Mar 16 '11 at 20:39

I have a: macBookPro3.1 Intel Core 2 Duo 2.4 Ghz

I have installed SL 10.6.6 over Tiger 10.4.11

I have 64- bit EFI Most of the extensions listed are YES for Intel 64-bit.

I have tried the two finger “6 and 4” procedure to boot into 64 bit mode.

I have tried that as an admin and as root.

No Joy. Same result as Abius X. Sys profile>Software> tells me

64 bit kernel and Extensions NO.

Have not tried entering the system changes via terminal yet. Waiting to get more info.

Anyone have any idea why these procedures are not working?

thanks f18a-nightlander

share|improve this answer
1  
According to KB #HT3770, the only MacBook Pros K64 is supported on are the Early 2008 through Mid 2010 versions; the MacBookPro3.1 was released in June, 2007. –  Gordon Davisson Mar 21 '11 at 6:01

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.